nighthawksetup

HOME
NETGEAR NIGHTHAWK EXTENDER SETUP
NETGEAR GENIE SETUP
+1 516-320-8459

Netgear EX7000 Setup

The Netgear Nighthawk EX7000 setup, or more correctly, the Netgear ac1900 extender setup, is quite easy. It can be done via WPS, Mywifiext, and the basic Nighthawk application. We will go into great detail about this in this article, so make sure to read until the end so you won’t need to refer to the manual again. In addition, this is one of the best and highest-rated range extenders made by Netgear.

Its high power amplifiers provide 700 nm of wireless power, which is strong enough to pass through walls and cover an area of up to 10,000 square feet.

NEW EXTENDER SETUP
Netgear Nighthawk EX7000 setup

Netgear Nighthawk EX7000 AC1900 Setup Using WPS

  • Reach for a power outlet close to your primary router to plug in the Netgear Nighthawk EX7000.
  • Await the extender’s Power LED turning solid green.
  • Take a couple of seconds to press the WPS button on the EX7000.
  • Press your router’s WPS button within two minutes.
  • Watch for the EX7000’s WPS LED to solidly turn white, signifying a successful connection.
  • Place the extender in the best possible spot—ideally, halfway between your router and the spot with spotty WiFi.
  • Wait for the Power LED to turn solid white after plugging the extender into the power outlet.
  • Using the same WiFi credentials as your primary network, connect your devices to the newly expanded WiFi network.

 

Note: If you need any assistance regarding your Netgear wifi extender, get in touch with us via the chat button you see on the bottom right corner of this page.

Netgear Nighthawk EX7000 AC1900 Setup Using Manual

  • The Netgear Nighthawk EX7000 should be plugged into a power socket close to your WiFi router.
  • Using a WiFi-capable device, connect to the extender’s default network, NETGEAR EXT.
  • Type mywifiext.net setup in the address bar of an open web browser.
  • To link the extender to your current WiFi network, follow the setup wizard’s instructions.
  • Select the WiFi network in your house, then, when prompted, enter the WiFi password.
  • Move the extender to the best location between the weak signal area and your router.
  • Using your WiFi login credentials, reconnect your devices to the expanded network.

 

Netgear EX7000 WiFi Extender Login

Netgear EX7000 WiFi Extender Login Steps

Netgear EX7000 WiFi Range Extender Firmware Update

  • Link the device to the internet connection NETGEAR EXT
  • Type mywifiext.net login in the address bar of an open web browser.
  • When asked, enter the default password and username.
  • For access to the extender’s settings, click Login.
  • Using the dashboard, adjust or modify the parameters.
  • Before leaving the setup screen, save any changes you make.

 

  • Link your gadget to the WiFi network of the Netgear EX7000.
  • Enter mywifiext.net setup into an open web browser to view the admin dashboard.
  • Enter your login information to log in.
  • Go to the Administration or Settings area.
  • Choose Firmware Update instead of checking for updates.
  • If there’s a new firmware version available, click Update.
  • Await the extender’s automated reboot and the installation of the update.

 

Netgear EX7000 Reset Process

  • Find out that the Netgear EX7000 is turned on.
  • On the side of the gadget, look for the reset button.
  • Press and hold the reset button with a paperclip or other comparable implement for approximately 7 seconds.
  • When the device reboots and returns to factory settings, release the button.
  • After the reset, adjust the extender’s settings as necessary.